Hornby HBA MGR Hopper (2002 Tooling)

from £2.80

A hand cast polyurethane resin wagon load for Hornby OO Gauge HBA MGR Hopper Wagon. (2002 Tooling)

Approximate size 91mm long x 31mm wide. Approximate weight 20g.

Please note these loads suit the 1st HBA wagon Hornby produced which was simply an old HAA wagon with an additional hood. Loads for the upgraded 2nd version, which is the wagon with sprung buffers for ease of identification, are listed separately as HFA loads. The same upgraded wagon carries both HBA and HFA TOPS coding.

To fit this load you will need to remove the canopy hood. I removed mine by simply running my finger nail along it's edge. The load has two slots milled across the top to allow for the replacement of the canopy with it's two cross braces.

This load can be supplied:

  • Plain Resin - this load will require primer before applying an enamel or acrylic paint.

  • Primed - this load has been pre-primed with good quality automotive primer ready to paint in a colour of  your choice.

  • Painted Coal - this load has been primed and spray painted with good quality automotive matt black paint to resemble coal and is ready to fit.

Wagon is NOT included!

This item is not suitable for children under 14 years.

Finish:
Quantity:
Add To Cart

A hand cast polyurethane resin wagon load for Hornby OO Gauge HBA MGR Hopper Wagon. (2002 Tooling)

Approximate size 91mm long x 31mm wide. Approximate weight 20g.

Please note these loads suit the 1st HBA wagon Hornby produced which was simply an old HAA wagon with an additional hood. Loads for the upgraded 2nd version, which is the wagon with sprung buffers for ease of identification, are listed separately as HFA loads. The same upgraded wagon carries both HBA and HFA TOPS coding.

To fit this load you will need to remove the canopy hood. I removed mine by simply running my finger nail along it's edge. The load has two slots milled across the top to allow for the replacement of the canopy with it's two cross braces.

This load can be supplied:

  • Plain Resin - this load will require primer before applying an enamel or acrylic paint.

  • Primed - this load has been pre-primed with good quality automotive primer ready to paint in a colour of  your choice.

  • Painted Coal - this load has been primed and spray painted with good quality automotive matt black paint to resemble coal and is ready to fit.

Wagon is NOT included!

This item is not suitable for children under 14 years.

A hand cast polyurethane resin wagon load for Hornby OO Gauge HBA MGR Hopper Wagon. (2002 Tooling)

Approximate size 91mm long x 31mm wide. Approximate weight 20g.

Please note these loads suit the 1st HBA wagon Hornby produced which was simply an old HAA wagon with an additional hood. Loads for the upgraded 2nd version, which is the wagon with sprung buffers for ease of identification, are listed separately as HFA loads. The same upgraded wagon carries both HBA and HFA TOPS coding.

To fit this load you will need to remove the canopy hood. I removed mine by simply running my finger nail along it's edge. The load has two slots milled across the top to allow for the replacement of the canopy with it's two cross braces.

This load can be supplied:

  • Plain Resin - this load will require primer before applying an enamel or acrylic paint.

  • Primed - this load has been pre-primed with good quality automotive primer ready to paint in a colour of  your choice.

  • Painted Coal - this load has been primed and spray painted with good quality automotive matt black paint to resemble coal and is ready to fit.

Wagon is NOT included!

This item is not suitable for children under 14 years.

Hornby 7 Plank Freelance Open Wagon LWB (2002)
from £2.55
Hornby LWB Large Mineral Open (Railroad)
from £2.55
Hornby HAA 32.5T MGR Hopper (2003 Tooling)
from £2.80
Hornby LMS 20 Ton Coke Hopper
from £3.00
Hornby Departmental ZFO Trout Ballast Hopper
from £2.75